Expanding on the reliable and time-tested technology of SCT’s RemoteCam™ platforms, the RemoteCamUSB2E™ is part of Sound Control Technologies’ next generation product portfolio for USB PTZ cameras. The RemoteCamUSB2E™ platform offers a cost and time saving alternative when integrating USB PTZ cameras into a wide variety of presentation spaces. The RemoteCamUSB2E™ Kits provide a reliable “transparent“ link between the camera and codec/head-end.
Supported Manufacturers: Lumens VC-TR1, Minrray UV510A.
Base Kit: Inclusive of RCU2E Modules, Kit Cables and Power Supply
RCU2E-CE Camera Interface Module
RCU2E-HE Codec/Head-End Interface Module
RCC-C002-0.3M RJ45 (RCU2E-CE™) to RJ45
RCC-M003-0.3M USB-A (RCU2E-CE™) to USB-A
RCC-H016-1.0M RJ45 (RCU2E-CE™) to RJ45
RCC-M004-1.0M USB-B (RCU2E-HE™) to USB-A
RCC-M014-1.0M USB-B (RCU2E-HE™) to USB-C
WPS-12 Power Supply.
- Extends camera power (no factory camera PSU required), PTZ control, audio and video over CAT5e/CAT6 cable up to 100m.
- Simple Plug and Play installation, no programming required.
- Ethernet streaming video supported on 100/1000 capable devices
- All hardware-specific camera and codec connection cables included.
- PowerSniffer included for testing SCTLink™ cable conductor continuity.
- Integrator only required to provide CAT5e/CAT6 SCTLink™ Cable.
- Field-upgradable firmware via microSD Card.
- Video Format: USB Video typically up to 1080p30/720p60
- UVC and IP Camera Control
- USB Tier Usage: 1 tier (hub) per linked set
- Two port 10/100/1000 Ethernet switch (RCU2E-HE™): Dual RJ45 connector
- 100/1000* Ethernet (RCU2E-CE™): RJ45 connector, Passive PoE, 48VDC up to 24W
- Power Out Connector (RCU2E-CE™): 5.5x2.5mm DC jack, 12VDC up to 1.2A
- USB Connector (RCU2E-CE™): USB-A for Data and 5V Camera Power up to 1.2A
- USB Connector (RCU2E-HE™): USB-B 2.0 for Host Connection
- Audio In/Out: 3.5mm TRS Jacks, Stereo Line Level Unbalanced
- SCTLINK™ CABLE SPECS:
- SCT recommends CAT6 or better cable for the SCTLink™. The use of a shielded cable, while not required for most platforms, is highly recommended.
- Proper termination and testing, along with good cable management, minimizes potential problems.
- 1000 Mbps only supported for SCTLink™ cables up to 15m
- Wiring Termination Standard T568A or T568B 100m Maximum Length (No Minimum Length)
- RCM™ Series On-Wall Mounts:
- Integrate mounting of the camera and the RCU2E-CE™ Camera End Module.
- Camera plates are laser cut to match the contour of the camera base.
- Cleanest mounting solution available, using an integrator-supplied US standard 2-Gang Box or Low Voltage Ring.
- Provides cable concealment and ease of installation.
- An RCW™ Series variant is also available for masonry or other solid walls where a 2-Gang Box or Low Voltage Ring cannot be used.
- RCR™ Series In-Wall Recessed Mounts:
- Integrate mounting of the camera and the RCU2E-CE™ Camera End Module.
- Three-piece all-metal solution with a common back box and bezel.
- Camera plates are laser cut to match the contour of the camera base.
- Camera plate has depth mounting options to meet specific requirements.
- Designed to meet ADA compliance in most cases (camera dependent).
- RCS™ Series Sheetrock Ceiling Mounts:
- Integrate mounting of the camera and the RCU2E-CE™ Camera End Module.
- Three-piece all-metal solution with a common Backbox.
- Camera specific with a custom cradle or a 1/4 20 bolt to securely hold the base of the camera
- RCT™ Series T-Bar Ceiling Mounts:
- Integrate mounting of the camera and the RCU2E-CE™ Camera End Module.
- Three-piece all-metal solution with a common T-Bar Bracket.
- Camera specific with a custom cradle or a 1/4 20 bolt to securely hold the base of the camera.
- RC-RKM™ 2RU 12” Deep Rack Shelf:
- Designed to mount the RCU2S-HE™, RCU2E-HE™, RC4-HE™, RC5-HE™, RC6-HE™, RC7-HE™, RC8- HE™, RTK-RX™ and RC-SDA™ modules, specific manufacturer codecs, and power supplies.
- Leaves access to rear of modules for clean and easy cabling, while providing proper ventilation
- RC-RK2™ 1RU 9” Deep Rack Shelf:
- Designed to mount two of our RCU2S-HE™, RCU2E-HE™, RC4-HE™, RC5-HE™, and RCSDA™ modules, and two of our WPS-12™ power supplies, while leaving access to rear of modules for clean and easy cabling.
- RC-RK4™ 1RU 14” Deep Rack Shelf:
- Designed to mount four of our RCU2S-HE™, RCU2E-HE™, RC4-HE™, RC5-HE™, and RCSDA™ modules, and four of our WPS-12™ power supplies, while leaving access to rear of modules for clean and easy cabling.
